Dynasil SOLID Cladding Stone Sealer

Description

Dynasil SOLID Cladding Stone Sealer, 1-litre Bottle or 5 Litre Drum

Impregnation Dynasil Solid for concrete, stone, plaster and plaster. Dynasil Solid is a preparation based on a mixture of small molecule active substances with a combined strengthening and hydrophobeizing effect. Used for both high-performance protective impregnation as well as for strengthening the surfaces destroyed by weather conditions.

Impregnation Dynasil Solid for concrete, stone, plaster

Silan-silicate impregnant impregnation with concomitant hydrophobizing and consolidating effects – solvent-free

Due to the small-molecular structure in the starting state, Dynasil Solid exhibits a very good penetration ability and react chemically in the building material in the presence of atmospheric moisture entering into a hydrophobic, ultraviolet resistant and weathering active substances. After the procedure, the active substance is stored on the walls of capillary and pores as a macromolecular layer, while strengthening the surface of impregnated mineral substrates. Due to the small-particleality of active substances, the impregnation procedure does not significantly affect the diffusion of water vapour.

Dynasil Solid stone impregnation is a preparation based on a mixture of small-mommeractive substances with a combined strengthening and hydrophobeifying effect. Used both for high-performance protective impregnation against water as well as for strengthening the groundings destroyed by weather conditions. Also used as a concrete impregnant, a stain impregnator, tile tile impregnator, brick impregnant

Impregnat Dynasil SOLID does not change the appearance of the surface, does not create a coating.

Impregnates Dynasil SOLID characteristics:

very fast formation of a hydrophobic effect on stone, concrete, plaster or plaster
in the area penetrated by the preparation, the substrate is strengthened
does not lead to visible changes on the surface of materials
does not change the colors of impregnated materials
– prevents water in the penetration, harmful substances (like water-soluble chloride ions)
reduces the propensity of the surface to dirt and the development of microorganisms
– effectiveness for small scratches and cracks up to 0.3mm
– also effective on damp substrates

Application of Dynasil SOLID impregnation:

The dynamo Dynasil SOLID is designed to impregnate both new facades in front of water and the influence of atmospheric factors, as well as to impregnation and enhance the disintegrated influence of atmospheric factors of building materials such as concrete, natural stones, ceramic materials, decorative details made of plaster. Especially recommended for highly absorbed and porous materials as an ecological alternative to solvent impregnation. Excellent impregnation of sandstones, lids and plaster.

As a preparation for hydrophobization and strengthening of all kinds of absorbent mineral absorbent absorbent materials. Especially useful for impregnation of substrates weakened by the action of atmospheric factors, as well as for high-efficiency protective impregnation of materials such as.

– Natural stones
– Mineral plasters
– Brick
– The Clinquer
– Concrete and the gazobeton
– Ceramic and concrete tiles
– Synthetic stones on the basis of mineral

The exact purpose of Dynasil SOLID:

Inside of the
Outside the world

Surface area:

Vertical

The material:

The Concrete
The Natural Stone
Painting plasters / coatings
Concrete of architecture
Sandstone of the
The Weed of the Weed
Decorative stone (gips)

The scope of protection:

Before the water

Finishing:

The non-deated surface

Appearance after the impregnation:

No change

If there are dirt on the ground, the Dynasil Renowal 500 cement removal agent should be used in advance

Dynasil SOLID consumption information:

Below are only the indicative consumption values for various substrates.
The Concrete 0.10 – 0.20 l/m 2
Mineral plasters 0.05 – 0.15 l/m 2
Calcium and sandstone 0.10 – 0.25 l/m 2
Natural small-poral stone 0.05 – 0.20 l/m 2
Brick 0.10 – 0.20 l/m 2
Machine Clinker 0.05 – 0.10 l/m 2
Hand-formed clinker 0.20 – 0.30 l/m 2

The consumption of the agent depends on the absorbability of the material and the technique of applying

Packaging:

1-litre (1 kg) or 5-litre (5 kg)

NOTES:
Dynasil Solid is not classified as dangerous in ADR and RID regulations